Num 1020/1040 installation and commissioning manual NUM Power 1020/1040/1060/1080 CNC Installation and Commissioning Manual Thousands of CNC Programming, Operating & Maintenance Manuals. How to reload parameter. For Num 1040w controller. Can you send for me manual for installation and setup this controller and the alarm list. The display Alarm.1, FHDL, and HOME Blinking. 4 How to Setup Parameter, Plc data & act for this controller. 5 What we do if backup battery lost voltage and after changge for new one. NUM CNC Manuals Instruction Manual and User Guide for NUM CNC. We have 19 NUM CNC manuals for free PDF download. Reminder for mac and iphone. NUM 1020/1040/1050/1060 T Addition to manual.
![Num 1020 cnc manual online Num 1020 cnc manual online](/uploads/1/2/6/4/126461594/397005179.jpg)
NUM 1020/1040/1060M G codes for cnc machinists who work on cnc mill with NUM cnc controls.
Num 1020 Cnc Manual Free
NUM 1020/1040/1060M G-Codes
Num 1020 Cnc Manual Download
G Code | Description |
---|---|
G00 | High-speed linear interpolation |
G01 | Linear interpolation at programmed feed rate |
G02 | Clockwise circular interpolation at programmed feed rate |
G03 | Counterclockwise circular interpolation at programmed feed rate |
G04 | Programmable dwell |
G06 | Spline curve execution command |
G09 | Accurate stop at end of block before going to next block |
G10 | Interruptible block |
G12 | Overspeed by handwheel |
G16 | Definition of tool axis orientation with addresses P, Q, R |
G17 | XY plane selection |
G18 | ZX plane selection |
G19 | YZ plane selection |
G23 | Circular interpolation defined by three points |
G29 | 3D tool correction (3 axes or 5 axes) |
G31 | Thread chasing cycle |
G40 | Tool radius offset (cutter compensation) cancel |
G41 | Left tool radius offset (cutter compensation) |
G42 | Right tool radius offset (cutter compensation) |
G43 | 3D correction with cylindrical tool |
G45 | Simple pocket cycle |
G46 | Pocket or facing cycles with any contours |
G48 | Spline curve definition |
G49 | Spline curve deletion |
G51 | Mirroring |
G52 | Programming of movements in absoluted dimensions with reference to the measurement origin |
G53 | DAT1 and DAT2 offset cancel |
G54 | DAT1 and DAT2 offset enable |
G59 | Programme origin offset |
G70 | Inch data input |
G71 | Metric data input |
G73 | Scaling factor cancel |
G74 | Scaling factor enable |
G75 | Emergency retraction subroutine declaration |
G76 | Transfer of the current values of «L» and «E» parameters into the part programme |
G76+/- | ISO programme or block creation/deletion |
G77 | Unconditional branch to a subroutine or block sequence with return |
G77 -i | Call of a subroutine return block |
G78 | Axis group synchronisation |
G79 | Conditional or unconditional jump to a sequence without return |
G79+/- | Temporary suspension of next block preparation in a sequence with movements |
G80 | Canned cycle cancel |
G81 | Centre drilling cycle |
G82 | Counterboring cycle |
G83 | Peck drilling cycle |
G84 | Tapping cycle |
G84 | Rigid tapping cycle |
G85 | Reaming cycle |
G86 | Boring cycle with indexed stop and clearance at hole bottom |
G87 | Drilling cycle with chip breaking |
G88 | Boring and facing cycle |
G89 | Boring cycle with dwell at hole bottom |
G90 | Programming in absolute dimensions with respect to the programme origin |
G91 | Programming in incremental dimensions with respect to the start of the block |
G92 | Programme origin preset |
G92 R | Programming of the tangential feed rate |
G93 | Feed rate expressed as inverse time (V/L) |
G94 | Feed rate expressed in millimetres, inches or degrees per minute |
G95 | Feed rate expressed in millimetres or inches per revolution |
G97 | Spindle speed expressed in revolutions per minute |
G104 | 3D curve smoothing |
G997 | Enabling and execution of all the functions stored in state G999 |
G998 | Enabling of execution of part of the functions processed in state G999 |
G999 | Suspension of execution and forcing of block concatenation |